Model Tech Yak 54 Manuel d'utilisateur télécharger pdf

1. Inventory the parts in your kit and familiarize

yourself with the assembly manual before start-

ing on this project. If this is your first aerobatic

model, get an experienced modeler from your

club to help you or call your local retailer.

2. Start working on the fuselage before the en-

gine is mounted. It is lighter and much easier to

handle on the workbench.

Rudder and tail wheel installation

1. Start with the Rudder before going to the

elevator since it will be easier to get to and

mount all the hardware.

2. Cut out the slots in the rudder to accept the G-

10 fiberglass dual rudder horns making sure they

are equal distance on both sides of the rudder to

prevent an off center throw. Apply 15 minute

epoxy to the horns making sure the holes are

filled and then slide the two keeper lock plates

in place at the same time. Wipe off any excess

epoxy with rubbing alcohol. Install the 4/40 ball

and swivel rod ends to keep the horns aligned

while the epoxy cures. Only snug up the bolts

and nylon insert nut so as not to crush the fiber-

glass horns. Make sure the push rod swivels are

mounted in the same width holes as the rudder

arm.

3. Trial fit the rudder hinges in place to make

sure it is free. You will glue this in later after

you get the tail wheel bracket mounted.

4. Draw a center line on the tail wheel mounting

block.

5. Tape the tail wheel bracket into place and

drill 3 holes the same size as the bracket holes.

6. Remove the access hatch in the rear.

Assembly Manual for Yak 54 -by Pilot RC

G-10 dual rudder Horns

Aluminum Steering peg

Elev Mtg tabs w/bolts

Access hatch

Slot for Rud cable

Mounting Screws CL

G-10 Elevator

G-10 Servo Arm

Use blue thread lock on all

bolts and blind nuts!

1 2 3 4 5 6 7 8 9 10

Résumé du contenu

Page 1 - Use blue thread lock on all

1. Inventory the parts in your kit and familiarize yourself with the assembly manual before start-ing on this project. If this is your first aerobati

Page 2

Hardware items included in kit: 1. Push Rods, threaded ends with bolts for Ailerons, Elevators and Rudder. 2. Mounting bolts and washers for Stabilize

Page 3 - Servo swivel clevis

7. Now drill out the holes with the same size bit as the blind nuts. 8. Install the blind nuts by using a large washer and the bolt to draw the bli

Page 4

Stab and Elevator Installation 1. Install the dual G-10 horns in place for the elevator horn before sliding the stab in place. 2. Remove the UltraCo

Page 5 - Engine installation

2. Remove the wheel collars from the axles. 3. Trial fit the wheel pants and make sure there is room for the outside shoulder nut to fit. Use you dr

Page 6

5 4. Install the 4-40 push rod swivel to the horn to make sure the holes are aligned. 5. Cut out the ultra Coat from the servo mounting holes. Note

Page 7

5. Now you need to decide if you are going to use a manual or servo to operate the choke. Drill holes in firewall for chock op-erating wire. 6. Rem

Page 8

14. Route the Halls Sensor cable and hold in place with a zip tie to the engine mount and lock the plugs together. 15. Route the rest of the servo ca

Page 9 - This is not a Toy!

8 Control Throws 1. After you set the control throws up and have a few flights under you belt, you can change the rates and amounts as well as moving

Page 10

Safety Precautions This is not a Toy! This R/C ARF kit and the model you build from this kit is not a Toy! It is capable of serious bodily harm and pr